 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| PRELIMINARY CYWM6934 WirelessUSB LSTM Radio Module 1.0 Features 2.0 Functional Description * The CYWM6934 LSTM 2.4-GHz DSSS Radio SoC Module includes radio (CYWUSB6934), antenna, and all external components * Complete Radio Module with PCB Trace Antenna * Operates in the unlicensed Industrial, Scientific, and Medical (ISM) band (2.4 GHz-2.483 GHz) * -90-dBm receive sensitivity * Up to 0-dBm output power * Range of up to 10 meters or more * Data throughput of up to 62.5 kbits/sec * SPI microcontroller interface (up to 2 MHz data rate) * Operating voltage from 2.7V to 3.6V * Small PCBA Design: 0.975" (24.38 mm) by 0.65" (16.25 mm) by 0.212" (5.3 mm) (L x W x H) * FCC Modular Approval Grant to meet FCC Part 15, EN 300 328-1, EN 301 489-1, and Industry Canada RSS-210 standards * An FCC Module Approval (MA) Grant provides customers significant cost savings, by allowing customers to adopt the CYWM6934 FCC ID into their own products The CYWM6934 WirelessUSB LSTM Radio Module offers a complete radio module solution for integration into existing or new 2.4-GHz products. The CYWM6934 is tested for functional operation and is FCC/ETSI(EU)/Industry pre-certified. The module is supplied with an integrated PCB trace antenna. The CYWM6934 is available in a small PCBA design and can be mounted horizontally to the device PCB via a 12-pin header. The pin-out of the header is shown in Figure 5-1. 3.0 Applications * PC Human Interface Devices (HID) -- Mice -- Keyboards -- Joysticks * Peripheral Gaming Devices -- Game Controllers -- Console Keyboards * General -- Presenter Tools -- Remote Controls -- Consumer Electronics -- Barcode Scanners -- POS Peripherals -- Toys CYWM6934 Module 12-pin 2mm header Vcc Bypass capacitors 2.0 pF 2.0 pF 3.3 nH Vcc RFIN RFOUT PCB Trace Antenna CYW USB6934 1.2 pF 10 WirelessUSB LS CYWUSB6934 Silicon 13MHz Crystal 2.2 nH 27 pF Cypress Semiconductor Corporation Document 38-16012 Rev. *A * 198 Champion Court * San Jose, CA 95134 * 408-943-2600 Revised October 10, 2006 [+] Feedback PRELIMINARY 3.1 Reference Documentation 4.1.1.3 Portable Application: For information on technical details of the WirelessUSB LSTM 2.4-GHz DSSS Radio SoC such as register settings, timing, application interfaces, clocking, and power management, refer to the data sheet of the CYWUSB6934 Radio SoC. CYWM6934 Module can be relocated and will have less than 20cm separation from human body. 4.1.2 Correct Installation: * Modules cannot be modified in any way * Modules must be used only in the operating range specified in the datasheets * Modules cannot be co-located within 20cm of another intentional radiator in the system * Must guarantee that end user cannot easily change antenna Note: Sidestepping these requirements is possible with additional testing and/or recertification. However, modular approval would no longer apply. 4.1.3 Correct Labeling: 3.2 Applications Support The CYWM6934 is available as a reference design, complete with PCB layout files, schematics, and a bill of materials. The CYWM6934 can be used with the CY3635 WirelessUSB N:1 sensor development kit, and the CY3632 WirelessUSB LS development kit via a 1 x 14 adaptor board. 4.0 Module Certification Details 4.1 Eligibility Requirements for Regulatory Module Approval The CYWM6934 LSTM Radio Module is a device that transmits and receives radio signals in accordance with the spectrum regulations for the 2.4-GHz unlicensed frequency range. Regional regulatory agency approval may be required to operate CYWM6934 throughout the world. Cypress Semiconductor Corporation has obtained regulatory approvals for the CYWM6934 to be used in specific countries. CYWM6934 was approved under the "Modular Approval (MA) Grant". This certification represents a significant cost savings to the OEM. The MA Grant provides that device manufacturers who incorporate CYWM6934 as tested and approved can be relieved from having to perform the Radio Regulatory certification portion of the respective agency certification. The MA Grant is valid only in countries[1.] that recognize the MA Grant certification process; the USA, Canada, Belgium, Denmark, France, Finland, Germany, Italy, Netherlands, Spain, Sweden, UK. In order to be able to take advantage of Cypress's modular certification in an end product, the following must be ensured: 1.) Correct Application 2.) Correct Installation 3.) Correct labeling 4.1.1 Correct Application: If end device containing a WirelessUSB LS Module will be sold or used in the USA, the enclosure of the product must display a label with the following basic elements: CYWM6934 Contains FCC ID: R8KUGWM1USHN33A If end device containing a WirelessUSB LS Module will be sold or used in Europe, the enclosure of the product must display a label with the following basic elements: CYWM6934 0122 If end device containing a WirelessUSB LS Module will be sold or used in Canada, the enclosure of the product must display a label with the following basic elements: There are three types of application considered for wireless modules and the LS has been verified to work with all three application types at pre-certified power output levels. However, other usages are possible with re-certification. The application types are defined as follows 4.1.1.1 Fixed Application: Module is in a permanent location and has atleast 2m separation from the human body. 4.1.1.2 Mobile Application: Module can be relocated and will have atleast 20cm separation from the human body. Note: 1. This list is as of march 2006. Please talk to your local Sales person for the current list. CYWM6934 This product contains Cypress WirelessUSB module Canadian Cert No IC: 5125A-UGWM1US As of March 2006, Japan does not recognize the "Modular Approval" certification. Regulatory certification for Japan (TELEC) must be acquired through typical approval procedures. These approvals are the sole responsibility of the OEM. Note: Even with modular approval, the end device still has to be tested for digital emissions compliance with all agencies as an electronic device. The modular approval only eliminates the need to test for compliance on RF transmissions. Page 2 of 9 Document 38-16012 Rev. *A [+] Feedback PRELIMINARY 4.2 User Guide Information Electronic device manufacturers using Cypress's Modular Approval are required to follow the below mentioned labeling practice on the container in which the device is marketed or in the product user's guide. This should be in accompaniment with other regulatory information. The text may be disbursed according to language or geographic regions if desired, but the exact text shown below must be maintained. 4.2.1 United States of America requirements: CYWM6934 * Not withstanding the Modular Approval for the Radio Device with associated interconnect and antennae, the end product configuration must meet digital emissions compliance and must be tested in accordance with FCC Part 15 requirements confirming radiated emissions are within specified limits. Applicable sections include: * Part 15 Section 15.109 Sub-paragraph A, Class B Radiated Emission Limits These emissions tests can be conducted by the manufacturer or by contacting an approved test facility equipped and certified accordingly. The results of these emissions tests are not required to be submitted to the FCC or Cypress, but should be kept on file by the OEM. * Cypress module can only be installed by the OEM and not by the user. It should not be installed in a user accessible location. * Any modifications to the radio will void the user's authority to operate the equipment. The OEM must not modify any aspect of the radio's mechanical and electrical configuration. * The OEM must include compliance information in their user information. * Although no additional regulatory work may be required for the radio, the host device is probably subject to other FCC authorizations as a digital device. DoC authorization is required for PCs and peripherals; verification is required for most other digital devices. Product Labeling Requirements FCC product labeling requirements stipulate an FCC label, including specific text, be placed on the device containing the CYWM6934 module. The product label must include the following text and must be affixed to the exterior of the OEM's product. (As shown in the `Correct Labeling' section 4.1.3) 4.2.2 proval Industry Canadian Requirements and Regulatory Ap- The device shall bear the following statement in a conspicuous location: "This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation". When the device is so small or for such use that it is not practical to place the statement specified under paragraph (a) of this section on it, the information required by this paragraph shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. However, the FCC identifier or the unique identifier, as appropriate, must be displayed on the device. The users manual or instruction manual for an intentional or unintentional radiator shall bear the following cautionary statement: Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment." 4.2.1.1 United States Regulatory Approval FCC Modular Approval (MA) The requirements for FCC Modular Approval were released in June 2000 in the FCC's Public Notice: FCC Public Notice DA 00-1407, Part 15 Unlicensed Modular Transmitter Approvals. Criteria for Modular Approval In our OEM instructions it is recommend that the following rules (required by FCC grants) be adhered to. * Cypress FCC ID label must appear on the outside of their product. FCC Public Notice DA 00-1407 instructs, "...if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: "Contains Transmitter Module FCC ID: XYZMODEL1" or "Contains FCC ID: XYZMODEL1." Any similar wording that expresses the same meaning may be used." * No co-location with other transmitters is allowed. By definition, co-location is when another radio or its antenna is located within 20 cm of our radio and it can transmit simultaneously with your radio. Only the antenna(s) that were certified with your radio may be used. Other antennas may be used only if they are of the same type (e.g. yagi, dipole, patch) and have the same or lower gain. Industry Canada regulatory approval typically conforms to the FCC in terms of emission levels and other regulatory requirements. It is the position of the Industry Canada agency that the OEM primarily responsibility for ensuring end product compliance. Cypress (Unigen) as grantee and supplier of the module maintains responsibility for the Modular Approved design. Criteria for Modular Approval In our OEM instructions it is recommend that the following rules (required by Industry Canada) be adhered to. * Cypress Industry Canada ID label must appear on the outside of their product.If the Industry Canada ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: "Contains Transmitter Module Canadian Cert No IC: XYZMODEL1" or "Contains Canadian Cert No IC: XYZMODEL1." Any similar wording that expresses the same meaning may be used. * No co-location with other transmitters is allowed. By definition, co-location is when another radio or its antenna is located within 20 cm of our radio and it can transmit simultaneously with your radio. Only the antenna(s) that were certified Document 38-16012 Rev. *A Page 3 of 9 [+] Feedback PRELIMINARY with your radio may be used. Other antennas may be used only if they are of the same type (e.g. yagi, dipole, patch) and have the same or lower gain. * Notwithstanding the Modular Approval for the Radio Device with associated interconnect and antennae, the end product configuration must meet digital emissions compliance and must be tested in accordance Industry Canada RSS-210 (Low Power License-Exempt Radio communication Devices) requirements confirming radiated emissions are within specified limits. Applicable sections include: * Part 15 Section 15.109 Sub-paragraph A, Class B Radiated Emission Limits These emissions tests can be conducted by the manufacturer or by contacting an approved test facility equipped and certified accordingly. The results of these emissions tests are not required to be submitted to Industry Canada or Cypress, but should be kept on file by the OEM. * Cypress module can only be installed by the OEM and not by the user. It should not be installed in a user accessible location. * Any modifications to the radio will void the user's authority to operate the equipment. The OEM must not modify any aspect of the radio's mechanical and electrical configuration. * The OEM must include compliance information in their user information. * Although no additional regulatory work may be required for the radio, the host device is probably subject to other FCC authorizations as a digital device. DoC authorization is required for PCs and peripherals; verification is required for most other digital devices. Note: Industry Canada generally follows the guidelines of the FCC for emissions level requirements. FCC end-product compliance certification results may be used to satisfy Industry Canada requirements. Please consult the Industry Canada, RSS 210 specifications to confirm interagency compliance. If comparable FCC testing has not been performed or if the specifications are not cross compliant, RSS 210 testing will be required. Product Labeling Requirements Industry Canada product labeling requirements stipulate specific text be placed on the device containing the CYWM6934 module. The product label must include the following text and must be affixed to the exterior of the OEM's product. (As shown in the `Correct Labeling' section 4.1.3) 4.2.3 proval European Union Requirements and Regulatory Ap- CYWM6934 apparatus, together with the declaration of conformity to the essential requirements." Ensuring regulatory compliance of the end product is the sole responsibility of the OEM. Cypress maintains responsibility for conformance of the CYWM6934, the interconnect, and the antennae as the manufacturer. The R&TTE directive maintains that first level compliance be reviewed by a "Notified Body" prior to general product marketing. This is not mandatory, but reduces the risk of the product being challenged for non-compliance. Although not specifically stated in the R&TTE Directive, corrections of noncompliance issues are the responsibility of the end product manufacturer. Criteria for Modular Approval In our OEM instructions it is recommend that the following rules (required by ETSI) be adhered to. * No co-location with other transmitters is allowed. By definition, co-location is when another radio or its antenna is located within 20 cm of our radio and it can transmit simultaneously with your radio. Only the antenna(s) that were certified with your radio may be used. Other antennas may be used only if they are of the same type (e.g. yagi, dipole, patch) and have the same or lower gain. * The end-product configuration must meet digital emissions compliance and must be tested in accordance with the European Union standards ETSI 300 328 (European Telecommunications Standard for 2.4 GHz ISM band Emissions) and ETSI 300 826 (Electromagnetic Compatibility). Detailed European Union regulatory standards documents may be obtained from the url: http://europa.eu.int/comm/enterprise/rtte/infor.htm These emissions tests can be conducted by the manufacturer or by contacting an approved test facility equipped and certified accordingly. The results of these emissions tests are not required to be submitted to the ETSI or Cypress, but should be kept on file by the OEM. * Cypress module can only be installed by the OEM and not by the user. It should not be installed in a user accessible location. * Any modifications to the radio will void the user's authority to operate the equipment. The OEM must not modify any aspect of the radio's mechanical and electrical configuration. * The OEM must include compliance information in their user information. * Although no additional regulatory work may be required for the radio, the host device is probably subject to other FCC authorizations as a digital device. DoC authorization is required for PCs and peripherals; verification is required for most other digital devices. Note: The European Union generally follows the guidelines of the FCC for emissions level requirements. FCC end-product compliance certification results, if available, may be used to satisfy EU requirements (Substitution Method). Please consult the ETSI 300 328 specifications to confirm inter-agency compliance. If comparable FCC testing has not been performed or if the specifications are not cross compliant, ETSI 300 328 testing will be required. Additionally, testing to Page 4 of 9 The requirements for EU Regulatory Approval were released in April 2000 in the EU R&TTE Directive. This directive supports self directed testing and certification for "harmonized" bands within OEM facilities or by third party. In the case of WirelessUSB, standards have become harmonized (although frequencies are not). The R&TTE directive no longer requires a Technical Construction File however; frequency notification to EU countries is still applicable. Article 6 of the R&TTE directive states: "The manufacturer or the person responsible for placing the apparatus on the market provides information for the user on the intended use of the Document 38-16012 Rev. *A [+] Feedback PRELIMINARY the ETSI 301 489-17 (immunity testing) is strongly recommended. Cypress assumes no responsibility for compliance of the end-product configuration. Product Labeling Requirements European Union product labeling requirements stipulate specific text be placed on the device containing the CYWM6934 module. The product label must include the following text and must be affixed to the exterior of the OEM's product. (As shown in the `Correct Labeling' section 4.1.3). This same information may be included in the product user manual, however this is not mandatory. Packaging and user CYWM6934 documentation must indicate the use restrictions of the endproduct (i.e. countries disallowing the operating frequencies of the CYWM6934). Note: The end-product must be labeled "CE" and to the right of the CE mark, the label should have '!' with a circle around it. The exclamation mark designates a non-harmonized frequency band. 5.0 Pin Definitions Name GND VCC IRQ nRESET MOSI nSS SCK MISO GND nPD N/C N/C Direction - - Output Input Input Input Input Output - Input - - Ground Supply voltage for the entire Radio Module (2.7V-3.6V). It is recommended that 3.3V be used for most applications. Interrupt signal from Radio Module to the MCU Active low reset signal from MCU to Radio Module Master out, slave in SPI signal from MCU to Radio Module Active low slave select signal from MCU to Radio Module SPI clock from MCU to Radio Module Master in, slave out SPI signal from Radio Module to MCU Ground Active low power-down signal from MCU to Radio Module No connect--leave open No connect--leave open Description Table 5-1. Pin Description Table for the CYWM6934 Pin QFN 1 2 3 4 5 6 7 8 9 10 11 12 12-pin 2mm header GND IRQ MOSI SCK GND N/C 1 3 5 7 9 11 2 4 6 8 10 12 V CC nRESET nSS MISO nPD N/C Figure 5-1. CYWM6934 Header Pin-out Document 38-16012 Rev. *A Page 5 of 9 [+] Feedback PRELIMINARY CYWM6934 Pin 1 Unit: Mils Figure 5-2. CYWM6934 Mechanical Drawing 12-pin 2mm Header's Pin1 Figure 5-3. CYWM6934 Top View Document 38-16012 Rev. *A Page 6 of 9 [+] Feedback ANT1 WIGGLE R VCC C1 0402 C2 2.0 pFd IND0402 6 9 16 28 29 32 41 42 44 45 VCC1 VCC2 VCC3 VCC4 VCC5 VCC6 VCC7 VCC8 VCC9 VCC10 GND 13 49 TAB Document 38-16012 Rev. *A 2.0 pFd U1 CYWUSB6934-48LFC L1 3.3 nH 0402 0402 C3 1.2 pFd nRESET 14 RESET RFIN RFOUT PACTL 46 5 34 L2 IND0402 C4 0402 VCC CLKOUT TV1 J1 1 3 5 7 9 11 1 3 5 7 9 11 2 4 6 8 10 12 nRESET nSS MISO nPD IRQ nPD 1 2 3 4 7 8 10 11 12 NC1 NC2 NC3 NC4 NC5 NC6 NC7 NC8 NC9 NC10 NC11 NC12 NC13 NC14 NC15 NC16 NC17 NC18 NC19 NC20 NC21 NC22 15 17 18 27 30 31 36 37 39 40 43 47 48 DIOVAL DIO IRQ PD HDR12_2MM 2 4 6 8 10 12 19 20 21 33 nSS MOSI MISO SCK 22 23 24 25 SS MOSI MISO SCK X13IN X13 X13OUT 35 38 26 2.2 nH 27 pFd Y1 Figure 5-4. CYWM6934 Schematic VCC 0402 IRQ MOSI SCK PRELIMINARY 13 MHz Crystal C6 0.1 uFd0402 C7 0.1 uFd0402 C8 0.1 uFd0402 C9 0.1 uFd0402 C10 0.1 uFd0402 C11 0.1 uFd 1206 C5 10 uFd 10v 1 CYWM6934 Page 7 of 9 [+] Feedback PRELIMINARY 6.0 Ordering Information Part Number CYWM6934 Radio Transceiver Module Package Name N/A N/A Package Type CYWM6934 Table 6-1. Ordering Information Operating Range Commercial This document is subject to change, and may be found to contain errors of omission or changes in parameters. For feedback or technical support regarding Cypress WirelessUSB products please contact Cypress at www.cypress.com. WirelessUSB LS is a trademark of Cypress Semiconductor Corporation. All product and company names mentioned in this document are the trademarks of their respective holders. Document 38-16012 Rev. *A Page 8 of 9 [+] Feedback PRELIMINARY Document History Page Document Title: CYWM6934 WirelessUSB LSTM Radio Module Document Number: 38-16012 REV. ** *A ECN NO. 329977 508598 Issue Date See ECN See ECN Orig. of Change BON UYR New data sheet Description of Change CYWM6934 Added `Modular Certification' details - For the USA, the EU and Canada. Document 38-16012 Rev. *A Page 9 of 9 (c) Cypress Semiconductor Corporation, 2005. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. [+] Feedback |
Price & Availability of CYWM693406
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |